Tec Vanlife USA

L Track Back Framing

$134.40 $125.00 Save 7%
Own this? Write the first review
Package Size

Solid threads behind the wall, no spinning rivnuts.

This powder coated steel plate mounts behind your L-track and gives every screw a built-in threaded nut to bite into. Its wide 2 1/8 in profile spreads the load across the van's sheet metal for a flat, stable anchor.

Fits: Universal, any van; matches the 12 hole pattern of all our 84 in L-track. Not included: mounting screws and rivets.

  • High tensile steel with a powder coated finish
  • Built-in threaded nuts end rivnut spin and jam
  • 84 in (2133 mm) long, 2 1/8 in (55 mm) wide
  • 12 pre-drilled holes that line up with the track

Choose your variant: 2 pack or 3 pack of 84 in plates.

Pairs with the 2mm Flanged, 6.8mm BEEFY Flanged, Squared and Rounded L-track.

See it on your van. Add the L Track Back Framing to your build in our 3D Van Builder and preview it on a real Sprinter before you buy.

Product Details

Why back framing

Rivnuts set straight into thin sheet metal can spin when you tighten or remove a screw, leaving a fastener stuck in the wall. The back framing puts fixed threads behind every track hole, so screws go in and come out clean.

The wide steel plate also spreads the load of beds, cabinets and gear across the wall instead of a few small holes.

What you get

  • 2 or 3 steel back framing plates, 84 in each, depending on the pack

Good to know

  • Screws and rivets are not included.
  • Built by Tec Vanlife. Reach out to our team at products@sandyvans.com or (619) 812-1903 with layout questions.

Fitment & Compatibility

Fits: Universal, any van

Not sure your build qualifies? Reach out to our team.

Specifications

MaterialHigh tensile steel, powder coated
Length84 in (2133 mm)
Width2 1/8 in (55 mm)
ThreadsBuilt-in nuts at each track hole
Mounting holes12, outer six 8 in on center, middle two 3 1/2 in on center
Recommended hardwareM6 stainless flat head screws and 1/8 in rivets (not included)
Packs2 pack or 3 pack
FitmentUniversal, any van

What's in the Box

  • Steel back framing plates, 84 in (2 or 3 per pack)
DIY FriendlyIntermediate
Drilling RequiredYes, for rivets

The plate goes on before your wall panels. Set it against the van's sheet metal where each L-track row will run, fasten it with 1/8 in rivets, then mount the track over it with M6 flat head screws into the built-in nuts. There's no separate manual from the manufacturer; Reach out to our team at products@sandyvans.com or (619) 812-1903 with questions or to book a shop install in San Diego.

Mistakes to avoid

  • Mounting the plate before you've planned panel seams and track rows
  • Forgetting screws and rivets; they're not in the box

Tools You'll Need

  • Drill
  • Rivet tool and 1/8 in rivets
  • M6 stainless flat head screws
  • Tape measure and level

See all Sandy Vans install videos & manuals →

How to choose L-track for your van

1. Flanged or flat

Flanged track has wings that clamp the edges of your wall and ceiling panels, so the track and paneling go in as one system. Flat profiles (squared and rounded) sit on top of the surface.

How to choose: Running 1/2 in or 3/8 in panels? Go flanged. Mounting to a finished wall, the floor or furniture? Go squared or rounded.

2. Load

The 2 mm flanged track carries a 500 lb working load limit. The 6.8 mm flanged, squared and rounded tracks carry 1,000 lb (manufacturer ratings).

How to choose: Beds, overhead cabinets and heavy gear get a 1,000 lb track. Light panels and soft storage are fine on 2 mm.

3. Profile and look

Squared track is 1.18 in (30 mm) wide with a crisp edge. Rounded track is 1.95 in (49.4 mm) wide with tapered sides that blend into the surface. Both come in anodized black or satin silver.

How to choose: Pick squared for a clean, narrow line; rounded where hands, feet or gear will brush past it.

4. What's behind the wall

Every track uses the same 12 hole pattern (8 in on center, 3 1/2 in for the middle pair), which lines up with the steel L-track back framing.

How to choose: Use back framing on any run that carries weight. It spreads the load and replaces rivnuts in thin sheet metal.

5. How many sections

Plan on 84 in sections with two rows of L-track per side. Sprinter 144: 4 driver side, 2 passenger side, 4 ceiling. Sprinter 170: 4, 2, 4. Transit 130: 3, 2, 3. Transit 148 and 148 Extended: 4, 2, 4. Two 84 in tracks cover the length of a 170 Sprinter or 148 Extended Transit; a 144 Sprinter or standard 148 Transit takes one full track plus a half section.

How to choose: Count your rows, then order 2 or 3 packs to match.

Before you order

  • Decide panels first: flanged track needs them, flat track doesn't.
  • Count rows and 84 in sections per wall and ceiling.
  • Order M6 or 1/4-20 flat head screws (not included).
  • Add back framing for load-bearing runs.
  • Pick a finish: black or silver.

How this track stacks up

Do I need back framing for my L-track?
Not required, but recommended. The back framing has the threaded nuts built in and lines up with the track's 12 hole pattern, so you skip setting rivnuts in the van's sheet metal, where a rivnut can spin or fail to set.
Which L-track does it work with?
All four 84 in tracks we carry: 2mm Flanged, 6.8mm BEEFY Flanged, High Capacity Squared and High Capacity Rounded. They share the same 12 hole pattern.
How does it attach to the van?
It sits behind the wall against the van's sheet metal. The manufacturer recommends 1/8 in rivets to set it and M6 stainless flat head screws to fasten the track. Hardware is not included.
How many do I need?
One plate per 84 in track section. Plan on 84 in sections with two rows of L-track per side. Sprinter 144: 4 driver side, 2 passenger side, 4 ceiling. Sprinter 170: 4, 2, 4. Transit 130: 3, 2, 3. Transit 148 and 148 Extended: 4, 2, 4. Two 84 in tracks cover the length of a 170 Sprinter or 148 Extended Transit; a 144 Sprinter or standard 148 Transit takes one full track plus a half section.
Will it fit my van?
Yes. It's universal and mounts to any van wall where you're running L-track.
How does shipping work on this item?
This item ships direct from the manufacturer, Tec Vanlife. Shipping is calculated at checkout for your address and may arrive separately from other items in your order.
Do you install products for customers?
Yes. Many SV products can be professionally installed at our San Diego shop. Reach out to our team to schedule. Email products@sandyvans.com or call 619-812-1903.
What is your shipping and return policy?
Most SV products ship free. For returns, see our Returns & Refunds policy or reach out to our team at products@sandyvans.com.
Can I reach a real person with questions?
Always. We are a small team in San Diego. Email products@sandyvans.com or call 619-812-1903 and you'll get a real answer, not a chatbot.
Where are you located?
9393 Trade Pl, San Diego, CA. Come visit the shop, we'd love to show you around.
Does Sandy Vans offer financing?
Yes. Many financing options are available. Set up a call with a sales associate to learn more.

Still have a question? Email the team and you'll get a real answer.

L Track Back Framing $125.00